What is a range hood?<\/h2>\n\n\n\n
A range hood is a kitchen appliance that aids in the reduction of smoke, dust, and grease produced by cooking. This is accomplished by dispersing these particles throughout the kitchen rather than allowing them to accumulate on the stovetops or in the air. This makes breathing easier and lowers your risk of respiratory problems.<\/strong><\/p>\n\n\n\n Installing a kitchen range hood can be intimidating, and many people make mistakes<\/a>. Here are some of the most common blunders when installing<\/a> a kitchen range hood. <\/strong><\/p>\n\n\n\n Connecting a range hood to a smaller duct than specified will result in performance loss and overheating issues, potentially leading to mechanical failure.<\/p>\n\n\n\n Furthermore, because of the ridged walls of flexible ducting, high-performance range hoods require rigid ducting. The airflow in flexible ducting is randomized rather than smooth, resulting in decreased performance and increased noise. Follow the manufacturer’s recommended duct size and type when installing a range hood.<\/p>\n\n\n\n Attaching a range hood to sheetrock alone is one of the most dangerous problems with range hood installation. Any range hood, regardless of weight, should be attached to structural beams or joists to provide proper long-term support. If the intended range hood location lacks a beam or joist, a cross-brace made of 24 s, 3\/4-inch plywood, or another strong material is an acceptable substitute.<\/p>\n\n\n\n If a range hood is attached to the sheetrock, it may appear stable initially, but the sheetrock anchors will loosen as they are used. Therefore, ensure that your installer installs the range hood correctly.<\/p>\n\n\n\n Though a range hood is recommended to be connected to an outside duct, this is not always possible. Many condominiums forbid any modifications to the building’s exterior walls. in this case, one would need to install a ductless range hood, also known as a recirculating range hood. <\/p>\n\n\n\n The hood uses charcoal filters to absorb odors before returning the cleaner air back into the room. Activated charcoal is a type of carbon specifically made to increase its porousness and thus maximize its surface area.<\/p>\n\n\n\n One of the most common errors in range hood installation is terminating the unit in an enclosed space, such as the attic or basement. Not only might the back-pressure cause the hood to malfunction, but warm, moist air from the kitchen into the attic space might cause a serious mold growth problem.<\/p>\n\n\n\n If you want to know more reasons why terminating your ehaust into an atic us a terribel idea, check out our post on why you shoudl never exhaust yoru rnage hood into an attic.<\/p>\n\n\n\n Outside ducts that exit through a side wall should be terminated with a duct cap, whereas roof-mounted ducts are sometimes terminated with a “U” shaped elbow, which allows air to exit while keeping rain and snow out. Make sure the cap is the same size and diameter as the duct; using a small cap will cause airflow and static pressure issues. <\/p>\n\n\n\n Regardless of the type of termination, a damper (also known as a backdraft and airflow controller) must be installed at the duct’s end. The damper prevents outside air from flowing back into the duct.<\/p>\n\n\n\n\n\n An electrical connection is a common error in appliance installation. The general rule is that if an appliance has exposed wires, it must be hardwired; if it has a plug, it must be plugged in. Following this rule will help you avoid manufacturer warranty problems and potential inspection issues. <\/p>\n\n\n\n Range hoods are typically installed 28-to-36-inches above the cooktop. However, Several factors influence how high a range hood should be installed above the cooking surface. Because cooking-polluted air does not rise in a perfectly straight line but spreads out, it’s a good idea to position the range hood low enough to capture the smoke and steam. <\/p>\n\n\n\n It’s also a good idea to place the range hood at a height where the lights are below eye level, which keeps the control panel within easy reach. Consult the range hood manufacturer’s recommendations.<\/p>\n\n\n\n We recommend contacting and hiring a local contractor to install your hood. It makes things much easier and will ensure you do things right first. <\/p>\n\n\n\n If you want more tips and insights, watch this video called “Range Hood Duct Installation Issues, Troubleshooting and Problem Solving”<\/em> from the Victory Range Hoods Youtube Channel.<\/p>\n\n\n\nCommon mistakes when installing a range hood<\/h2>\n\n\n\n
1. Duct Size and type<\/h3>\n\n\n\n
2. Improper Support<\/h3>\n\n\n\n
3. Ductless and recirculation installation<\/h3>\n\n\n\n
![\"Image](\"https:\/\/rangehoodhomeland.com\/wp-content\/uploads\/2022\/10\/Image-of-a-kitchen-with-wooden-shelves-and-countertop-and-a-range-hood-over-an-oven.-source-max-vakhtbovych-Pexels-1024x683.jpg\" "\\"\\"")
Source: Max Vakhtbovych, Pexels<\/figcaption><\/figure>\n\n\n\n4. Inpropper exhuat location<\/h3>\n\n\n\n
5. Using the wong duct cap<\/h3>\n\n\n\n
6. Impropper wiring<\/h3>\n\n\n\n
7. Installation height<\/h3>\n\n\n\n
Should you install your range hood yourself or hire a contractor?<\/h2>\n\n\n\n